Klein MODBOX ROLLING DRAWER Front Casters - PREORDER
Klein MODBOX Rolling Drawer Front Casters are the best way to create a more maneuverable MODBOX workstation!
PREORDER SATUS - Orders Will begin shipping END of November!
These Front Casters keep pressure off your MODBOX Rolling Drawer Box handle, placing it at a comfortable angle and enabling the box to spin in any direction with ease.
Install each caster in seconds without damaging your MODBOX Rolling DRAWER!
*** Remember to USE COMMON SENSE when using your front casters! ***
Important DO’s and DONT’s
DO expect to easily install and remove your casters without using any tools! After installation, remember to regularly check that both casters are fully touching the bottom of the box!
DO NOT expect these casters to function as well as Klein’s 10 inch wheels on the rear of your box!
DO expect these casters to increase maneuverability on the recommended surfaces listed below!
DO NOT expect these casters to assist when rolling over rough or uneven surfaces - including gaps by elevator doors or bumps at ends of ramps. In these situations, USE ONLY 10 inch Rear Wheels (lower the handle enough to raise both casters off the ground or even remove them)!
DO expect to remove your casters when you want your stack to be completely level!
Special Features:
4 integrated anchor points (one on the front and side of each caster) for attaching a rope, bungee cord, ratchet strap and more - 50 lb load limit
Individual locks on each caster
Low Profile Design
Recommended Surfaces:
Plywood/ OSB/ Subfloor
Commercial Carpet
Epoxy Floors
Vinyl/Laminate Flooring
Polished Concrete
*UNFINISHED CONCRETE MAY CAUSE ACCELERATED WEAR ON THE CASTERS - Consider adding replacement casters to your cart for future use (: *
NOTE: These casters are specifically made for the Rolling Drawer Box and will not work on the standard MODBOX Roller!
Klein MODBOX Rolling Drawer Front Casters are the best way to create a more maneuverable MODBOX workstation!
PREORDER SATUS - Orders Will begin shipping END of November!
These Front Casters keep pressure off your MODBOX Rolling Drawer Box handle, placing it at a comfortable angle and enabling the box to spin in any direction with ease.
Install each caster in seconds without damaging your MODBOX Rolling DRAWER!
*** Remember to USE COMMON SENSE when using your front casters! ***
Important DO’s and DONT’s
DO expect to easily install and remove your casters without using any tools! After installation, remember to regularly check that both casters are fully touching the bottom of the box!
DO NOT expect these casters to function as well as Klein’s 10 inch wheels on the rear of your box!
DO expect these casters to increase maneuverability on the recommended surfaces listed below!
DO NOT expect these casters to assist when rolling over rough or uneven surfaces - including gaps by elevator doors or bumps at ends of ramps. In these situations, USE ONLY 10 inch Rear Wheels (lower the handle enough to raise both casters off the ground or even remove them)!
DO expect to remove your casters when you want your stack to be completely level!
Special Features:
4 integrated anchor points (one on the front and side of each caster) for attaching a rope, bungee cord, ratchet strap and more - 50 lb load limit
Individual locks on each caster
Low Profile Design
Recommended Surfaces:
Plywood/ OSB/ Subfloor
Commercial Carpet
Epoxy Floors
Vinyl/Laminate Flooring
Polished Concrete
*UNFINISHED CONCRETE MAY CAUSE ACCELERATED WEAR ON THE CASTERS - Consider adding replacement casters to your cart for future use (: *
NOTE: These casters are specifically made for the Rolling Drawer Box and will not work on the standard MODBOX Roller!
Klein MODBOX Rolling Drawer Front Casters are the best way to create a more maneuverable MODBOX workstation!
PREORDER SATUS - Orders Will begin shipping END of November!
These Front Casters keep pressure off your MODBOX Rolling Drawer Box handle, placing it at a comfortable angle and enabling the box to spin in any direction with ease.
Install each caster in seconds without damaging your MODBOX Rolling DRAWER!
*** Remember to USE COMMON SENSE when using your front casters! ***
Important DO’s and DONT’s
DO expect to easily install and remove your casters without using any tools! After installation, remember to regularly check that both casters are fully touching the bottom of the box!
DO NOT expect these casters to function as well as Klein’s 10 inch wheels on the rear of your box!
DO expect these casters to increase maneuverability on the recommended surfaces listed below!
DO NOT expect these casters to assist when rolling over rough or uneven surfaces - including gaps by elevator doors or bumps at ends of ramps. In these situations, USE ONLY 10 inch Rear Wheels (lower the handle enough to raise both casters off the ground or even remove them)!
DO expect to remove your casters when you want your stack to be completely level!
Special Features:
4 integrated anchor points (one on the front and side of each caster) for attaching a rope, bungee cord, ratchet strap and more - 50 lb load limit
Individual locks on each caster
Low Profile Design
Recommended Surfaces:
Plywood/ OSB/ Subfloor
Commercial Carpet
Epoxy Floors
Vinyl/Laminate Flooring
Polished Concrete
*UNFINISHED CONCRETE MAY CAUSE ACCELERATED WEAR ON THE CASTERS - Consider adding replacement casters to your cart for future use (: *
NOTE: These casters are specifically made for the Rolling Drawer Box and will not work on the standard MODBOX Roller!
