ToughBuilt Front Casters are the best way to create a more maneuverable StackTech workstation!
The Casters keep pressure off your StackTech Rolling Box handle, placing it at a comfortable angle and enabling the box to spin in any direction with ease.
Install in seconds without damaging your StackTech Rolling Box!
https://youtube.com/shorts/FRqHZAOfZAA?feature=share
Special Features:
An integrated anchor point (for attaching a rope, bungee cord, or ratchet strap) is on the side of each caster
Casters have individual locks
Low Profile Design
Want more storage capacity? Pair the Front Casters with the TBRA E-Track Adapters
Easily add StackTech's 2 shelf system onto the front of your Rolling Boxes using 4, 6 or 8 adapters.
*** Remember to USE COMMON SENSE when using your front casters! ***
Important DO’s and DONT’s
DO expect to easily install and remove your casters with just a Philips screwdriver.
DO NOT expect these casters to function as well as Toughbuilt’s Nine inch wheels on the rear of your box!
DO expect these casters to increase maneuverability on the recommended surfaces listed below!
DO NOT expect these casters to assist when rolling over rough or uneven surfaces - including gaps by elevator doors or bumps at ends of ramps. In these situations, USE ONLY 9 inch Rear Wheels (lower the handle enough to raise both casters off the ground or even remove them)!
DO expect to remove your casters when you want your stack to be completely level!
Note: If you want a level stack at all times, consider building the folding TB ST Casters.
Special Features:
2 integrated anchor points (one on the side of each caster) for attaching a rope, bungee cord, ratchet strap and more - 50 lb load limit
Individual locks on each caster
Recommended Surfaces:
Plywood/ OSB/ Subfloor
Commercial Carpet
Epoxy Floors
Vinyl/Laminate Flooring
Polished Concrete
*UNFINISHED CONCRETE MAY CAUSE ACCELERATED WEAR ON THE CASTERS
ToughBuilt Front Casters are the best way to create a more maneuverable StackTech workstation!
The Casters keep pressure off your StackTech Rolling Box handle, placing it at a comfortable angle and enabling the box to spin in any direction with ease.
Install in seconds without damaging your StackTech Rolling Box!
https://youtube.com/shorts/FRqHZAOfZAA?feature=share
Special Features:
An integrated anchor point (for attaching a rope, bungee cord, or ratchet strap) is on the side of each caster
Casters have individual locks
Low Profile Design
Want more storage capacity? Pair the Front Casters with the TBRA E-Track Adapters
Easily add StackTech's 2 shelf system onto the front of your Rolling Boxes using 4, 6 or 8 adapters.
*** Remember to USE COMMON SENSE when using your front casters! ***
Important DO’s and DONT’s
DO expect to easily install and remove your casters with just a Philips screwdriver.
DO NOT expect these casters to function as well as Toughbuilt’s Nine inch wheels on the rear of your box!
DO expect these casters to increase maneuverability on the recommended surfaces listed below!
DO NOT expect these casters to assist when rolling over rough or uneven surfaces - including gaps by elevator doors or bumps at ends of ramps. In these situations, USE ONLY 9 inch Rear Wheels (lower the handle enough to raise both casters off the ground or even remove them)!
DO expect to remove your casters when you want your stack to be completely level!
Note: If you want a level stack at all times, consider building the folding TB ST Casters.
Special Features:
2 integrated anchor points (one on the side of each caster) for attaching a rope, bungee cord, ratchet strap and more - 50 lb load limit
Individual locks on each caster
Recommended Surfaces:
Plywood/ OSB/ Subfloor
Commercial Carpet
Epoxy Floors
Vinyl/Laminate Flooring
Polished Concrete
*UNFINISHED CONCRETE MAY CAUSE ACCELERATED WEAR ON THE CASTERS
